godson2f cpu internal uart test... just before superio init... PMON2000 MIPS Initializing. Standby... ERRORPC=75ca3d69 CONFIG=00030932 PRID=00006303 enable register space of MEMORY DDR2 config begin... DDR2 config end DDR2 DLL locked 006f0004 disable register space of MEMORY MEMORY TYPE AND SIZE PROBE. tmpsize = 2000000000000001type : ddr2, size = 0x00000400MB jlliu : rom speed reg : 0x00000f0f Init SDRAM Done! Sizing caches... Init caches... godson2 caches found Init caches done, cfg = 00030932 Copy PMON to execute location... start = 0x81000000 s0 = 0x3ec00000 TEST _EDATA... a1040000a1000000 copy text section done. Copy PMON to execute location done. sp=80ffc000Uncompressing Bios.....................OK,Booting Bios FREQ FREI DONE TTYI TTYD ENVI MAPV in envinit nvram bfc7f000 NVRAM@bfc7f000 STDV 80100000: heap is already above this point SBDD 5536 PPCIH PCIS PCIR PCIW otg base = 0xb40c2000 cs5536 otg configured for USB DEVICE. cs5536 fixup : otg ok. cs5536 fixup : lpc ok. NETI RTCL PCID in configure mainbus0 (root) localbus0 at mainbus0 pcibr0 at mainbus0 pci0 at pcibr0 bus 0 rtk0 at pci0 dev 6 function 0 vendor/product: 0x10ec/0x8169 (network, ethernet)tag=3000,reg=10,value=b201 8169 iobase =bfd0b200 before softreset -> 0 After softreset -> 0 r8169: Reset device success r8169: mac_version == RTL_GIGA_MAC_VER_X (0004) r8169: phy_version == RTL_GIGA_PHY_VER_G (0002) MAC addr is 00:23:9e:ff:d7:8a 8129 10ec 8169 10ec 8169 4020 a101 2300 ff9e 8ad7 cd15 f7c2 8000 0000 0000 1300 Identified chip type is 'RTL8169s/8110s'. r8110 at 0xbfd0b200, 00:23:9e:ff:d7:8a r8169: mac_version == RTL_GIGA_MAC_VER_X (0004) r8169: phy_version == RTL_GIGA_PHY_VER_G (0002) r8169: MAC version != 0 && PHY version == 0 or 1 r8169: Do final_reg2.cfg Set MAC Reg C+CR Offset 0x82h = 0x01h media option is deprecated. rtl8169_set_speed_xmii in if attach rtl_chip_info: RTL8169s/8110s, 4 r8110: link down interrupt established!rtk1 at pci0 dev 7 function 0 vendor/product: 0x10ec/0x8169 (network, ethernet)tag=3800,reg=10,value=b101 8169 iobase =bfd0b100 before softreset -> 0 After softreset -> 0 r8169: Reset device success r8169: mac_version == RTL_GIGA_MAC_VER_X (0004) r8169: phy_version == RTL_GIGA_PHY_VER_G (0002) MAC addr is 00:23:9e:ff:d7:8b 8129 10ec 8169 10ec 8169 4020 a101 2300 ff9e 8bd7 cd15 f7c2 8000 0000 0000 1300 Identified chip type is 'RTL8169s/8110s'. r8110 at 0xbfd0b100, 00:23:9e:ff:d7:8b r8169: mac_version == RTL_GIGA_MAC_VER_X (0004) r8169: phy_version == RTL_GIGA_PHY_VER_G (0002) r8169: MAC version != 0 && PHY version == 0 or 1 r8169: Do final_reg2.cfg Set MAC Reg C+CR Offset 0x82h = 0x01h rtl8169_set_speed_xmii in if attach rtl_chip_info: RTL8169s/8110s, 4 r8110: link down interrupt established!vendor/product: 0x1095/0x3114 (mass storage, miscellaneous) at pci0 dev 8 function 0 not configured vendor/product: 0x1022/0x2090 (bridge, ISA) at pci0 dev 14 function 0 not configured pciide0 at pci0 dev 14 function 2 vendor/product: 0x1022/0x209a (mass storage, IDE): DMA, ch 0 wired to compat, ch 1 wired to compat st0=a0,st1=b0 st0=a0,st1=b0 st0=a0,st1=b0 st0=a0,st1=b0 vendor/product: 0x1022/0x2093 (multimedia, audio) at pci0 dev 14 function 3 not configured ohci0 at pci0 dev 14 function 4 vendor/product: 0x1022/0x2094 (serialbus, USB)OHCI 8ff87000 initialized ok drive at ohci0 devnum 1, Product OHCI Root Hub not configured vendor/product: 0x1022/0x2095 (serialbus, USB) at pci0 dev 14 function 5 not configured vendor/product: 0x1022/0x2096 (serialbus, USB) at pci0 dev 14 function 6 not configured vendor/product: 0x1022/0x2097 (serialbus, USB) at pci0 dev 14 function 7 not configured out configure devconfig done. network configure 'rtk0:192.168.1.5' bootp=8000bb40 rtl_chip_info: RTL8169s/8110s, 4 r8110: link down HSTI SYMI SBDE Configuration [Bonito,EL,NET,IDE] Version: PMON2000 2.1 (Bonito) #187: 2008I 08? 19? ?l?9:52 CST. Supported loaders [srec, elf, bin] Supported filesystems [net, fat, fs, disk, iso9660, socket, tty, ram] This software may be redistributed under the BSD copyright. Copyright 2000-2002, Opsycon AB, Sweden. Copyright 2006, Lemote Corp. Ltd., ICT CAS. CPU Loongson2F @ 800.02 MHz / Bus @ 66.00 MHz Memory size 1024 MB (256 MB Low memory, 768 MB High memory) . Primary Instruction cache size 64kb (32 line, 4 way) Primary Data cache size 64kb (32 line, 4 way) Secondary cache size 512kb AUTO Press to execute loading image:/dev/ram@bc000000 Press other key to abort. .. Loading file: /dev/ram@bc000000 (elf) (elf) 0x81000000/2359296 + 0x81240000/8240(z) + 39 syms| Entry address is 81000000 zero at v0 v1 a0 a1 a2 a3 00000000 00000000 00000000 00000000 00000006 aff7fcd8 aff7fcf4 80093dc0 t0 t1 t2 t3 t4 t5 t6 t7 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 s0 s1 s2 s3 s4 s5 s6 s7 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 t8 t9 k0 k1 gp sp s8 ra 00000000 00000000 00000000 00000000 00000000 aff7fcb8 00000000 8005bd70 loaded at: 81000000 81240000 zimage at: 81002000 8123F16C Uncompressing Linux at load address 80200000 Now, booting the kernel... [ 0.000000] Linux version 2.6.30-fuloong2f (root@jianada) (gcc version 4.4.2 (Debian 4.4.2-3) ) #1 PREEMPT Thu Dec 17 02:47:52 CST 2009 [ 0.000000] busclock=66000000, cpuclock=800020000, memsize=256, highmemsize=768 [ 0.000000] console [early0] enabled [ 0.000000] CPU revision is: 00006303 (ICT Loongson-2) [ 0.000000] FPU revision is: 00000501 [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable) [ 0.000000] memory: 0000000030000000 @ 0000000090000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00030000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] 0: 0x00024000 -> 0x00030000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64864 [ 0.000000] Kernel command line: root=/dev/sda1 ide-core.noprobe=0.0 ide-core.noprobe=0.1 console=ttyS0,115200 PMON_VER=1.2.0 ide_core.ignore_cable=0 [ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes. [ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes. [ 0.000000] NR_IRQS:128 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Console: colour dummy device 80x25 [ 0.004000] ram_console: buffer (null), invalid size 0, datasize 18446744073709551604 [ 0.008000] Dentry cache hash table entries: 131072 (order: 6, 1048576 bytes) [ 0.016000] Inode-cache hash table entries: 65536 (order: 5, 524288 bytes) [ 0.056000] Memory: 1034096k/1048576k available (4372k kernel code, 13776k reserved, 1277k data, 256k init, 0k highmem) [ 0.060000] Calibrating delay loop... 530.43 BogoMIPS (lpj=1060864) [ 0.164000] Security Framework initialized [ 0.168000] Mount-cache hash table entries: 1024 [ 0.172000] Checking for the daddi bug... no. [ 0.180000] net_namespace: 1752 bytes [ 0.184000] xor: measuring software checksum speed [ 0.208000] 8regs : 2028.000 MB/sec [ 0.232000] 8regs_prefetch: 1688.000 MB/sec [ 0.256000] 32regs : 1632.000 MB/sec [ 0.280000] 32regs_prefetch: 1484.000 MB/sec [ 0.284000] xor: using function: 8regs (2028.000 MB/sec) [ 0.288000] NET: Registered protocol family 16 [ 0.292000] initialize the cs5536 i2c function [ 0.304000] bio: create slab at 0 [ 0.308000] SCSI subsystem initialized [ 0.312000] usbcore: registered new interface driver usbfs [ 0.316000] usbcore: registered new interface driver hub [ 0.320000] usbcore: registered new device driver usb [ 0.396000] raid6: int64x1 429 MB/s [ 0.464000] raid6: int64x2 523 MB/s [ 0.532000] raid6: int64x4 512 MB/s [ 0.600000] raid6: int64x8 388 MB/s [ 0.600000] raid6: using algorithm int64x2 (523 MB/s) [ 0.604000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot [ 0.608000] pci 0000:00:06.0: PME# disabled [ 0.612000] pci 0000:00:07.0: PME# supported from D1 D2 D3hot [ 0.616000] pci 0000:00:07.0: PME# disabled [ 0.620000] cs5536 acc latency 0x0 [ 0.624000] slot: 6, pin: 1, irq: 36 [ 0.628000] slot: 7, pin: 1, irq: 37 [ 0.632000] slot: 8, pin: 1, irq: 38 [ 0.636000] NetLabel: Initializing [ 0.640000] NetLabel: domain hash size = 128 [ 0.644000] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.648000] NetLabel: unlabeled traffic allowed by default [ 0.652000] NET: Registered protocol family 2 [ 0.656000] IP route cache hash table entries: 8192 (order: 2, 65536 bytes) [ 0.660000] TCP established hash table entries: 32768 (order: 5, 524288 bytes) [ 0.664000] TCP bind hash table entries: 32768 (order: 4, 262144 bytes) [ 0.668000] TCP: Hash tables configured (established 32768 bind 32768) [ 0.672000] TCP reno registered [ 0.672000] NET: Registered protocol family 1 [ 0.680000] cpufreq: Loongson-2F CPU frequency driver. [ 0.684000] VFS: Disk quotas dquot_6.5.2 [ 0.688000] Dquot-cache hash table entries: 2048 (order 0, 16384 bytes) [ 0.692000] msgmni has been set to 2021 [ 0.696000] alg: No test for stdrng (krng) [ 0.700000] async_tx: api initialized (sync-only) [ 0.704000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.708000] io scheduler noop registered [ 0.712000] io scheduler anticipatory registered [ 0.716000] io scheduler deadline registered [ 0.720000] io scheduler cfq registered (default) [ 0.724000] isapnp: Scanning for PnP cards... [ 1.084000] isapnp: No Plug & Play device found [ 1.100000] rtc: SRM (post-2000) epoch (2000) detected [ 1.104000] Real Time Clock Driver v1.12b [ 1.108000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.116000] console handover: boot [early0] -> real [ttyS0] 16550A [ 1.128000] brd: module loaded [ 1.132000] Uniform Multi-Platform E-IDE driver [ 1.136000] amd74xx 0000:00:0e.2: UDMA100 controller [ 1.140000] amd74xx 0000:00:0e.2: IDE controller (0x1022:0x209a rev 0x01) [ 1.144000] amd74xx 0000:00:0e.2: IDE port disabled [ 1.148000] amd74xx 0000:00:0e.2: not 100% native mode: will probe irqs later [ 1.152000] ide: ignoring cable detection for ide0 [ 1.156000] ide: skipping probe for hda [ 1.160000] ide: skipping probe for hdb [ 1.164000] ide0: BM-DMA at 0x5070-0x5077 [ 1.168000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 1.172000] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports [ 1.176000] ide-gd driver 1.18 [ 1.180000] Driver 'sd' needs updating - please use bus_type methods [ 1.184000] sata_sil 0000:00:08.0: Applying R_ERR on DMA activate FIS errata fix [ 1.188000] scsi0 : sata_sil [ 1.192000] scsi1 : sata_sil [ 1.196000] scsi2 : sata_sil [ 1.200000] scsi3 : sata_sil [ 1.204000] ata1: SATA max UDMA/100 mmio m1024@0x400c2000 tf 0x400c2080 irq 38 [ 1.208000] ata2: SATA max UDMA/100 mmio m1024@0x400c2000 tf 0x400c20c0 irq 38 [ 1.212000] ata3: SATA max UDMA/100 mmio m1024@0x400c2000 tf 0x400c2280 irq 38 [ 1.216000] ata4: SATA max UDMA/100 mmio m1024@0x400c2000 tf 0x400c22c0 irq 38 [ 1.220000] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.224000] r8169 0000:00:06.0: no PCI Express capability [ 1.228000] eth0: RTL8169sc/8110sc at 0x90000000400c2400, 00:23:9e:ff:d7:8a, XID 18000000 IRQ 36 [ 1.232000] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.236000] r8169 0000:00:07.0: no PCI Express capability [ 1.240000] eth1: RTL8169sc/8110sc at 0x90000000400c2500, 00:23:9e:ff:d7:8b, XID 18000000 IRQ 37 [ 1.244000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.248000] PCI: Enabling device 0000:00:0e.5 (0000 -> 0002) [ 1.252000] ehci_hcd 0000:00:0e.5: EHCI Host Controller [ 1.256000] ehci_hcd 0000:00:0e.5: new USB bus registered, assigned bus number 1 [ 1.284000] ehci_hcd 0000:00:0e.5: irq 11, io mem 0x400c1000 [ 1.300000] ehci_hcd 0000:00:0e.5: USB 0.0 started, EHCI 1.00 [ 1.304000] usb usb1: configuration #1 chosen from 1 choice [ 1.312000] hub 1-0:1.0: USB hub found [ 1.312000] hub 1-0:1.0: 4 ports detected [ 1.320000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.324000] PCI: Enabling device 0000:00:0e.4 (0000 -> 0002) [ 1.328000] ohci_hcd 0000:00:0e.4: OHCI Host Controller [ 1.332000] ohci_hcd 0000:00:0e.4: new USB bus registered, assigned bus number 2 [ 1.336000] ohci_hcd 0000:00:0e.4: irq 11, io mem 0x400c0000 [ 1.428000] usb usb2: configuration #1 chosen from 1 choice [ 1.432000] hub 2-0:1.0: USB hub found [ 1.436000] hub 2-0:1.0: 4 ports detected [ 1.440000] Initializing USB Mass Storage driver... [ 1.444000] usbcore: registered new interface driver usb-storage [ 1.448000] USB Mass Storage support registered. [ 1.452000] usbcore: registered new interface driver libusual [ 1.456000] usbcore: registered new interface driver ums-alauda [ 1.460000] usbcore: registered new interface driver ums-cypress [ 1.464000] usbcore: registered new interface driver ums-datafab [ 1.468000] usbcore: registered new interface driver ums-freecom [ 1.472000] usbcore: registered new interface driver ums-isd200 [ 1.476000] usbcore: registered new interface driver ums-jumpshot [ 1.480000] usbcore: registered new interface driver ums-karma [ 1.484000] usbcore: registered new interface driver ums-onetouch [ 1.488000] usbcore: registered new interface driver ums-sddr09 [ 1.492000] usbcore: registered new interface driver ums-sddr55 [ 1.496000] usbcore: registered new interface driver ums-usbat [ 1.504000] i8042.c: No controller found. [ 1.508000] Trying to free nonexistent resource <0000000000000060-000000000000006f> [ 1.512000] mice: PS/2 mouse device common for all mice [ 1.516000] md: raid0 personality registered for level 0 [ 1.520000] md: raid1 personality registered for level 1 [ 1.524000] md: raid10 personality registered for level 10 [ 1.528000] md: raid6 personality registered for level 6 [ 1.532000] md: raid5 personality registered for level 5 [ 1.536000] md: raid4 personality registered for level 4 [ 1.540000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1.544000] usbcore: registered new interface driver hiddev [ 1.548000] usbcore: registered new interface driver usbhid [ 1.552000] usbhid: v2.6:USB HID core driver [ 1.556000] NET: Registered protocol family 17 [ 1.584000] ata1.00: ATA-8: ST31000333AS, CC1F, max UDMA/133 [ 1.588000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 1.648000] ata1.00: configured for UDMA/100 [ 1.668000] scsi 0:0:0:0: Direct-Access ATA ST31000333AS CC1F PQ: 0 ANSI: 5 [ 1.672000] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [ 1.676000] sd 0:0:0:0: [sda] Write Protect is off [ 1.680000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.684000] sda: sda1 sda2 sda3 [ 1.728000] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.008000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 2.020000] ata2.00: ATA-8: ST31000528AS, CC37, max UDMA/133 [ 2.024000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 2.044000] ata2.00: configured for UDMA/100 [ 2.064000] scsi 1:0:0:0: Direct-Access ATA ST31000528AS CC37 PQ: 0 ANSI: 5 [ 2.068000] sd 1:0:0:0: [sdb] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [ 2.072000] sd 1:0:0:0: [sdb] Write Protect is off [ 2.076000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.080000] sdb: sdb1 sdb2 [ 2.104000] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.404000] ata3: SATA link down (SStatus 0 SControl 310) [ 2.728000] ata4: SATA link down (SStatus 0 SControl 310) [ 2.732000] Initalizing network drop monitor service [ 2.736000] md: Waiting for all devices to be available before autodetect [ 2.740000] md: If you don't use raid, use raid=noautodetect [ 2.744000] md: Autodetecting RAID arrays. [ 2.748000] md: Scanned 0 and added 0 devices. [ 2.752000] md: autorun ... [ 2.752000] md: ... autorun DONE. [ 2.760000] EXT3-fs: INFO: recovery required on readonly filesystem. [ 2.764000] EXT3-fs: write access will be enabled during recovery. [ 2.816000] kjournald starting. Commit interval 5 seconds [ 2.820000] EXT3-fs: recovery complete. [ 2.828000] EXT3-fs: mounted filesystem with writeback data mode. [ 2.832000] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 2.836000] Freeing unused kernel memory: 256k freed Mount failed for selinuxfs on /selinux: No such file or directory INIT: version 2.86 booting hostname: the specified hostname is invalid Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Feb 13 03:49:06 UTC 2010 (warning). Activating swap...[ 4.112000] Adding 506000k swap on /dev/sda2. Priority:-1 extents:1 across:506000k done. [ 4.148000] EXT3 FS on sda1, internal journal Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Sat Feb 13 03:49:07 UTC 2010 (warning). Cleaning up ifupdown.... Loading kernel modules...done. Setting up LVM Volume Groups[ 5.140000] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com Reading all physical volumes. This may take a while... Found volume group "spool" using metadata type lvm2 3 logical volume(s) in volume group "spool" now active . Checking file systems...fsck 1.41.0 (10-Jul-2008) done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...[ 6.720000] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [ 6.728000] SGI XFS Quota Management subsystem [ 6.760000] XFS mounting filesystem dm-0 [ 7.056000] XFS mounting filesystem dm-1 done. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ [ 8.284000] r8169: eth0: link up Listening on LPF/eth0/00:23:9e:ff:d7:8a Sending on LPF/eth0/00:23:9e:ff:d7:8a Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.1.1 bound to 192.168.1.5 -- renewal in 881450693 seconds. if-up.d/mountnfs[eth0]: waiting for interface eth1 before doing NFS mounts (warning). [ 12.120000] NET: Registered protocol family 10 [ 12.124000] lo: Disabled Privacy Extensions [ 12.276000] r8169: eth1: link down [ 12.280000] ADDRCONF(NETDEV_UP): eth1: link is not ready done. INIT: Entering runlevel: 2 Starting enhanced syslogd: rsyslogd. Starting OpenBSD Secure Shell server: sshd. Starting MTA: exim4. Starting periodic command scheduler: crond.